Toyota Kijang Innova Workshop Manuals and Repair Manuals

To change the engine oil in a Toyota Kijang Innova, start by locating the oil drain plug underneath the engine. Use a wrench to remove the plug and let the old oil drain out completely. Once the oil has drained, replace the drain plug and remove the oil filter. Install a new oil filter and fill the engine with the recommended amount of new oil, as specified in the owner's manual.

To change the windshield wiper blades on a Toyota Kijang Innova, lift the wiper arm away from the windshield and locate the release tab on the wiper blade assembly. Press the tab and slide the blade out of the wiper arm. Align the new wiper blade with the arm and slide it in until it clicks into place. Gently lower the wiper arm back onto the windshield and repeat the process for the other wiper blade.

To check and refill the coolant in a Toyota Kijang Innova, first, ensure that the engine is cool. Locate the coolant reservoir, usually a translucent plastic tank, and check the coolant level against the "Full" and "Low" markings. If the level is low, remove the cap and add a mixture of coolant and distilled water to bring it to the appropriate level. It is important to use the correct coolant type as specified in the owner's manual. Once the coolant level is correct, reinstall the cap securely.

To check the tire pressure in a Toyota Kijang Innova, start by locating the tire pressure monitoring system (TPMS) button, usually located on the dashboard. Press and hold the TPMS button until the TPMS light blinks twice, indicating that the system is in calibration mode. Then, go to each tire and use a tire pressure gauge to check the pressure. Compare the measured pressure to the recommended pressure listed on the driver's side door jamb or in the owner's manual. Inflate or deflate the tires as necessary to achieve the correct pressure.

If your Toyota Kijang Innova's brake pedal feels spongy, start by checking the brake fluid level in the master cylinder reservoir. If it is low, add the recommended brake fluid type until it reaches the appropriate level. Inspect the brake lines for any leaks or damage

If you are experiencing a misfiring engine in your Toyota Kijang Innova, start by checking for any visible signs of wear or damage to the spark plugs and ignition coils. Replace any damaged components as necessary. Next, inspect the fuel injectors for clogs or leaks and clean or replace them if needed. Additionally, check the air intake system for any restrictions or obstructions. If the issue persists, it is recommended to have the vehicle diagnosed by a professional mechanic to determine the exact cause of the misfire.

To replace a burnt-out headlight in a Toyota Kijang Innova, first, open the hood and locate the back of the headlight assembly. Disconnect the electrical connector by pressing the release tab and pulling it away from the bulb. Then, twist the bulb socket counterclockwise and remove it from the assembly. Finally, remove the old bulb and replace it with a new one, making sure not to touch the glass portion of the new bulb. Reassemble the components in reverse order.

To replace a faulty fuel pump in a Toyota Kijang Innova, start by relieving the fuel system pressure by disconnecting the fuel pump fuse or relay and running the engine until it stalls. Disconnect the negative battery cable and locate the fuel pump assembly, usually located inside the fuel tank. Disconnect the electrical connectors and fuel lines attached to the pump, then remove the mounting screws or bolts. Replace the old fuel pump with a new one and reassemble the components in reverse order, ensuring all connections are properly secured.

To replace a faulty oxygen sensor in a Toyota Kijang Innova, start by locating the sensor, which is typically mounted in the exhaust system. Disconnect the electrical connector attached to the sensor and use an oxygen sensor socket or a wrench to remove it from the exhaust pipe. Install the new oxygen sensor by threading it into the exhaust pipe and tightening it securely. Reconnect the electrical connector and clear any stored fault codes using a diagnostic tool.

To replace the cabin air filter in a Toyota Kijang Innova, start by locating the filter housing, usually located behind the glove compartment. Open the glove compartment and remove any contents, then push in the tabs on the sides of the compartment to release it and allow it to drop down. Locate the filter housing cover and remove the screws or clips holding it in place. Take out the old filter and replace it with a new one, ensuring it is properly aligned. Reinstall the cover, glove compartment, and any other components that were removed.

To replace the serpentine belt in a Toyota Kijang Innova, start by locating the belt routing diagram, usually found on a sticker under the hood. Use a wrench or tensioner tool to relieve tension on the belt and slide it off the pulleys. Install the new belt by following the belt routing diagram and ensuring it is properly seated on all pulleys. Finally, release the tensioner and double-check the belt tension to ensure proper operation.

To reset the maintenance required light in a Toyota Kijang Innova, insert the key into the ignition and turn it to the "ON" position without starting the engine. Press and hold the trip meter reset button until the trip meter displays "000000" or the maintenance light starts flashing. Release the button and turn off the ignition. When you turn on the vehicle again, the maintenance required light should be reset.

If the air conditioning system in your Toyota Kijang Innova is not working properly, start by checking the fuse related to the AC system and replacing it if necessary. Next, inspect the AC compressor for any visible damage or leaks. Check the refrigerant level using a pressure gauge and add refrigerant if needed. If the issue persists, it is recommended to consult a professional mechanic for further diagnosis and repair.

It is recommended to replace the spark plugs in a Toyota Kijang Innova every 30,000 to 40,000 miles or as specified in the owner's manual. Regularly inspect the spark plugs for signs of wear, such as a worn electrode or excessive carbon buildup. If you notice any issues, it is best to replace the spark plugs sooner to ensure optimal engine performance and fuel efficiency.

If your Toyota Kijang Innova's battery is dead, you can jump-start the vehicle using jumper cables and another vehicle with a charged battery. Connect the positive (red) cable to the positive terminal of the dead battery, and then connect the other end of the positive cable to the positive terminal of the charged battery. Next, connect the negative (black) cable to the negative terminal of the charged battery and the other end to an unpainted metal surface on the dead vehicle. Start the engine of the vehicle with the charged battery and let it run for a few minutes before attempting to start your Toyota Kijang Innova.