Smart Car Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Smart Car

The Nissan Skyline is a line of compact cars, sports cars and compact executive cars originally produced by the Prince Motor Company starting in 1955, and then by Nissan after the two companies merged in 1966. In May 1998, the EN34, HR34, ER34 and BNR34 marked the introduction of the more fuel-efficient and environmentally friendly RB25DET NEO engine. The RB20E engine was discontinued in the R34 base model (GT), and the RB20DE, after last being used in the R32 Skyline, was reintroduced inupdated NEO guise. The R34 GT powered by the RB20DE NEO, coupled with a five-speed gearbox, became the most fuel-efficient straight-six Skyline to date (of any shape). Only the GT-T coupe variant was sold in New Zealand and Hong Kong from 1997 to 2000 respectively. They were the only two countries besides Japan that sold the R34 GT-T model Skylines new.

Smart Car FAQ's

How do I change a flat tire on my Smart Car?

To change a flat tire on a Smart Car, you will need to locate the spare tire, jack, and lug wrench in the car's trunk. Following the step-by-step instructions provided in the manual, you will need to safely jack up the car, remove the lug nuts, replace the flat tire with the spare, and tighten the lug nuts securely. It is important to exercise caution and refer to the manual for accurate instructions and safety precautions.

How do I change the engine oil filter in my Smart Car?

To change the engine oil filter in a Smart Car, you will need to locate the oil filter housing, remove the old filter using an appropriate tool, and replace it with a new filter. It is important to refer to the manual for the correct filter type, tightening torque, and any additional steps specific to your Smart Car model. Properly changing the oil filter ensures clean oil circulation and prevents contaminants from damaging the engine.

How do I check the battery condition in my Smart Car?

To check the battery condition in a Smart Car, you will need to use a multimeter or a battery tester. Ensure the engine is turned off and all electrical accessories are switched off. Connect the multimeter or battery tester to the battery terminals, observing the polarity. The reading should indicate the battery's voltage. A healthy battery typically measures around 12.6 volts or higher. If the battery voltage is significantly lower, it may indicate a weak or failing battery that requires replacement.

How do I check the transmission fluid level in my Smart Car?

Checking the transmission fluid level in a Smart Car requires following specific steps outlined in the car's manual. Typically, the car needs to be warmed up, parked on a level surface, and the transmission fluid dipstick needs to be removed and wiped clean before reinserting and checking the fluid level. It is crucial to refer to the manual for accurate instructions as improper transmission fluid levels can result in transmission issues and potential damage.

How do I jump-start my Smart Car?

To jump-start a Smart Car, you will need a set of jumper cables and another vehicle with a fully charged battery. Connect the positive (red) cable to the positive terminal of the dead battery, then connect the other end to the positive terminal of the charged battery. Next, connect the negative (black) cable to the negative terminal of the charged battery and attach the other end to a metal part of the car with the dead battery. Start the engine of the vehicle with the charged battery and let it run for a few minutes before attempting to start the Smart Car.

How do I replace a blown fuse in my Smart Car?

To replace a blown fuse in a Smart Car, you will need to locate the fuse box, usually located in the dashboard or engine compartment. Use the fuse diagram in the car's manual to identify the specific fuse related to the malfunctioning component. Once identified, use a fuse puller or a pair of needle-nose pliers to remove the blown fuse and replace it with a new fuse of the same rating. It is important to only use fuses with the correct amperage to prevent electrical issues or damage to the vehicle's systems.

How do I reset the maintenance light on my Smart Car dashboard?

To reset the maintenance light on a Smart Car, you can follow a series of specific steps mentioned in the car's manual. Typically, this involves turning the ignition on without starting the engine, selecting the trip meter display, and holding down the reset button until the maintenance light resets. It is important to note that the reset procedure may vary depending on the Smart Car model and year, so referring to the manual is crucial for accurate instructions.

How often should I change the oil in my Smart Car?

It is recommended to change the oil in your Smart Car every 7,500 miles or once a year, whichever comes first. Regular oil changes are essential to maintain the engine's performance and prolong its lifespan. Neglecting timely oil changes can lead to increased friction, reduced fuel efficiency, and potential engine damage.

How often should I replace the air filter in my Smart Car?

The air filter in a Smart Car should be replaced every 30,000 miles or as indicated by the maintenance schedule. A clean air filter allows for proper air flow to the engine, ensuring efficient combustion and preventing dust and debris from entering the engine. Neglecting to replace a clogged air filter can lead to reduced engine performance and increased fuel consumption.

How often should I replace the spark plugs in my Smart Car?

The spark plugs in a Smart Car typically have a recommended replacement interval of every 30,000 miles or as indicated by the maintenance schedule. New spark plugs ensure proper ignition, fuel efficiency, and engine performance. Neglecting to replace worn-out spark plugs can lead to misfires, decreased power, and reduced fuel economy.

What is the recommended coolant for my Smart Car?

The recommended coolant for a Smart Car is a mixture of water and antifreeze with a 50:50 ratio. This coolant mixture provides proper cooling and protection against freezing and overheating. It is essential to use the correct coolant type as specified in the manual, as using incompatible coolant can lead to coolant leaks, engine overheating, and potential damage to the cooling system.

What is the recommended interval for replacing the brake pads in my Smart Car?

The recommended interval for replacing the brake pads in a Smart Car varies depending on driving habits, conditions, and the type of brake pads used. Typically, it is advised to inspect the brake pads regularly and replace them when they have worn down to a thickness of 2-3mm. Timely replacement of brake pads ensures optimal braking performance and prevents damage to the brake rotor.

What is the recommended interval for replacing the timing belt in my Smart Car?

The recommended interval for replacing the timing belt in a Smart Car varies depending on the model and year. Typically, it is advised to replace the timing belt every 60,000 to 90,000 miles or as specified by the maintenance schedule. Replacing the timing belt at the recommended mileage is crucial to prevent the risk of belt failure, which can lead to severe engine damage.

What is the recommended tire pressure for my Smart Car?

The recommended tire pressure for a Smart Car varies depending on the model and tire size. It is generally advised to maintain the tire pressure between 29-36 psi. Proper tire pressure not only improves fuel efficiency but also ensures optimal handling, braking, and tire lifespan. It is important to check the tire pressure regularly, especially before long trips or when carrying heavy loads.

What type of fuel should I use in my Smart Car?

Smart Cars are designed to run on premium unleaded gasoline with an octane rating of 91 or higher. Using the recommended fuel ensures optimal performance and efficiency. Using lower octane fuels may result in engine knocking, decreased power, and reduced fuel economy.